Rad Power Bike Throttle Not Working: Fixed

The most common reason your Rad Power Bike throttle might not work is a faulty throttle sensor. The throttle sensor is a small component that tells the bike how much power to apply to the motor. If the throttle sensor is damaged or corroded, it won’t be able to send the correct signal to the bike, and the throttle will not work.

As an experienced Rad Power Bike owner and mechanic, I’ve seen my fair share of throttle problems. One time, my throttle stopped working altogether. I checked the throttle sensor for damage or corrosion, but it looked fine. I then cleaned the throttle housing for dirt and debris, which didn’t fix the problem either. I was about to contact Rad Power Bikes for assistance when I decided to take a closer look at the throttle cable. The cable was loose, so I tightened it up. And that did the trick! The throttle started working again like a charm.

In this article, I’ll walk you through the steps to troubleshoot and fix a Rad Power Bike throttle that is not working. I’ll also provide some tips on how to prevent your throttle from malfunctioning in the future.

Why Is My Rad Power Bike Throttle Not Working?

There are a few reasons why your Rad Power Bike throttle might not work. The most common reasons are:

• Faulty Throttle Sensor
• Dirt or Debris Buildup in The Throttle Housing
• Loose or Damaged Throttle Cable
• Software Glitch

1. Faulty Throttle Sensor

The throttle sensor is a small component that tells the bike how much power to apply to the motor. If the throttle sensor is damaged or corroded, it won’t be able to send the correct signal to the bike, and the throttle will not work.

Solution

Checking the throttle sensor for damage or corrosion is a good idea. You can do this by following these steps:

1. Locate the throttle sensor. It’s usually located on the handlebar, near the throttle grip.
2. Inspect the throttle sensor for any visible damage.
3. Use a multimeter to check the resistance of the throttle sensor. The resistance should be within the specified range for your bike.

It must be replaced if the throttle sensor is damaged or the resistance is outside the specified range. To replace the throttle sensor, you will need to follow these steps:

1. Turn off the bike and disconnect the battery.
2. Remove the throttle housing.
3. Disconnect the old throttle sensor from the wiring harness.
4. Connect the new throttle sensor to the wiring harness.
5. Reinstall the throttle housing.
6. Connect the battery and turn on the bike.

2. Dirt or Debris Buildup in The Throttle Housing

The throttle housing is the plastic housing that surrounds the throttle sensor. If dirt or debris gets into the throttle housing, it can block the signal from the throttle sensor to the bike, and the throttle will not work.

Solution

To fix this, you must clean the throttle housing with a mild soap and water solution. You can do this by following these steps:

1. Locate the throttle housing. It’s usually located on the handlebar, near the throttle grip.
2. Remove the throttle grip and housing.
3. Use a soft brush to clean out the throttle housing.
4. Reinstall the throttle grip and housing.

If the throttle is still not working after cleaning the throttle housing, you may need to replace the throttle sensor.

3. Loose or Damaged Throttle Cable

The throttle cable is the cable that connects the throttle sensor to the motor. If the throttle cable is loose or damaged, it won’t be able to transmit the signal from the throttle sensor to the motor, and the throttle will not work.

Solution

To fix a loose or damaged throttle, you will need to tighten or replace the throttle cable. To detect if the throttle is loose, you’ll need to:

1. Locate the throttle cable. It’s usually located on the handlebar, near the throttle grip.
2. Inspect the throttle cable for any visible damage.
3. Try pulling on the throttle cable. If it moves freely, then it’s not loose.

To tighten the throttle cable, you will need to follow these steps:

1. Locate the throttle cable.
2. Use a wrench to tighten the cable clamp.
3. Test the throttle to make sure it is working properly.

When you check the throttle cable and notice it’s damaged, you’ll need to replace it. To replace the throttle cable, you will need to follow these steps:

1. Turn off the bike and disconnect the battery.
2. Remove the old throttle cable.
3. Install the new throttle cable.
4. Connect the battery and turn on the bike.

4. Software Glitch

Rad Power Bikes regularly releases software updates for its bikes. If you haven’t updated your bike’s software in a while, there may be a software glitch that is causing the throttle to not work.

Solution

To fix a software glitch, you will need to update your bike’s software. To update your bike’s software, follow these steps:

1. Connect your bike to a computer with an internet connection.
2. Download the latest software update from the Rad Power Bikes website.
3. Install the software update on your bike.
4. Test the throttle once the software update is installed to ensure it works properly.

How to Troubleshoot a Rad Power Bike Throttle That Is Not Working

If your Rad Power Bike throttle is not working, you can try the following troubleshooting steps:

Step 1: Check the Throttle Sensor for Damage or Corrosion.

The throttle sensor is a small component that tells the bike how much power to apply to the motor. If the throttle sensor is damaged or corroded, it won’t be able to send the correct signal to the bike, and the throttle will not work. To check the throttle sensor, you will need to remove the throttle housing. If the throttle sensor is damaged or corroded, you will need to replace it.

Step 2: Clean the Throttle Housing for Dirt and Debris.

The throttle housing is the plastic housing that surrounds the throttle sensor. If dirt or debris gets into the throttle housing, it can block the signal from the throttle sensor to the bike, and the throttle will not work. To clean the throttle housing, you will need to remove the throttle housing and use a mild soap and water solution to clean the inside.

Step 3: Inspect the Throttle Cable for Looseness or Damage.

The throttle cable is the cable that connects the throttle sensor to the motor. If the throttle cable is loose or damaged, it won’t be able to transmit the signal from the throttle sensor to the motor, and the throttle will not work. To inspect the throttle cable, you must locate the cable and look for any signs of damage or looseness. If the throttle cable is damaged or loose, you must replace it.

Step 4: Update Your Bike’s Software

Rad Power Bikes regularly releases software updates for its bikes. If you haven’t updated your bike’s software in a while, there may be a software glitch that is causing the throttle to not work. To update your bike’s software, you will need to connect your bike to a computer with an internet connection. You can then download the latest software update from the Rad Power Bikes website and install it on your bike.

If you have tried all of these troubleshooting steps and your throttle is still not working, then you may need to contact Rad Power Bikes for assistance. They will be able to diagnose the problem and recommend a solution.

Tips for Preventing Your Rad Power Bike Throttle From Not Working

1. Keep your bike clean and free of dirt and debris. This will help prevent problems with the throttle as well as other components on the bike.
2. Inspect your bike regularly for any signs of damage or looseness. If you see anything that looks out of place, be sure to fix it right away.
3. Update your bike’s software regularly. This will help to ensure that your bike is running properly and that any known software glitches are fixed.
4. Be careful not to overtighten the throttle cable. If the cable is too tight, it can stress the throttle sensor and cause it to fail.
5. If you are uncomfortable working on your bike, be sure to take it to a qualified mechanic for regular maintenance.

Conclusion

Your Rad Power Bike throttle should be responsive, smooth, and reliable. When it starts to act up, it can be a real nuisance. In some cases, it can even be dangerous.

If your Rad Power Bike throttle is not working properly, it’s important to troubleshoot the problem as soon as possible. The most common reasons for a non-working throttle are a faulty throttle sensor, dirt or debris in the throttle housing, a loose or damaged throttle cable, or a software glitch.

In this article, I have discussed the common reasons why a Rad Power Bike throttle might not be working and some tips for troubleshooting and preventing the problem.